done read sensors

Arduino/Arduino_/Arduino.ino

@@ -1,70 +0,0 @@
-#include <SoftwareSerial.h>
-#include <Wire.h>
-#include "SIM800L.h"
-#include <BME280I2C.h>
-
-#define SIM800_RX_PIN 10
-#define SIM800_TX_PIN 11
-#define SIM800_RST_PIN 7
-
-SIM800L* sim800l;
-BME280I2C bme;
-
-
-const char APN[] = "TM";
-String BASE_URL = "http://2.238.194.8/index.php?";
-//String BASE_URL = "https://postman-echo.com/get?";
-
-String s = "";
-char URL[100];
-
-
-int anemometerPin = 6;
-int anemometerVal = 0;
-int anemometerState = 0;
-unsigned long anemometerDuration = 0;
-unsigned long startime = 0;
-unsigned long timer = 0;
-int windSpeed = 0;
-
-float temperature = 0;
-float humidity = 0;
-float pressure = 0;
-
-int northPin = 4;
-int eastPin = 5;
-int southPin = 2;
-int westPin = 3;
-
-int timerLimit = 10000;//300000; // 5 minutes
-String windDirection = "";
-bool printSensorsData = true;
-
-
-void setup() {
-  // Initialize Serial Monitor for debugging
-  Serial.begin(9600);
-  while(!Serial);
-
- pinMode(13, OUTPUT);
- digitalWrite(13, HIGH);
-
-  // Initialize a SoftwareSerial
-  SoftwareSerial* serial = new SoftwareSerial(SIM800_RX_PIN, SIM800_TX_PIN);
-  serial->begin(9600);
-  delay(1000);
-
-  // Initialize SIM800L driver with an internal buffer of 200 bytes and a reception buffer of 512 bytes, debug disabled
-  sim800l = new SIM800L((Stream *)serial, SIM800_RST_PIN, 200, 512);
-
-  // Setup modules
-  setupSIM800L();
-  setupBME280();
-  timer = millis() + timerLimit;
-}
-
-void loop() {
- 
-  getWind();
-
-}

Arduino/Arduino_/GetData.ino

@@ -1,36 +0,0 @@
-
-void getWind() {
-
-  windDirection = "";
-  anemometerVal = digitalRead(anemometerPin);
-
-  if ((anemometerState == 1) && (anemometerVal == 0)) {
-    anemometerDuration = millis() - startime;
-    startime = millis();
-    windSpeed = 2500.0/anemometerDuration;
-  }
-
-  anemometerState = anemometerVal;
-
-  if(millis() >= timer) {
-
-    Serial.println("--------------------------");
-    timer = millis() + timerLimit;
-
-    if(digitalRead(northPin)) {windDirection = windDirection + "N";}
-    if(digitalRead(southPin)) {windDirection = windDirection + "S";}
-    if(digitalRead(eastPin)) {windDirection = windDirection + "E";}
-    if(digitalRead(westPin)) {windDirection = windDirection + "W";}
-
-    if(printSensorsData) {
-      Serial.print("Wind speed:\t");
-      Serial.print(windSpeed);
-      Serial.println("Km/h");
-
-      Serial.print("Wind direction:\t");
-      Serial.println(windDirection);
-
-    }
-    //sendRequest();
-  }
-}

Arduino/Arduino_/GetSensor.ino

@@ -1,14 +0,0 @@
-void getBME280Data() {
-
-   float temp(NAN), hum(NAN), pres(NAN);
-
-   BME280::TempUnit tempUnit(BME280::TempUnit_Celsius);
-   BME280::PresUnit presUnit(BME280::PresUnit_Pa);
-
-   bme.read(pres, temp, hum, tempUnit, presUnit);
-
-   temperature = temp;
-   humidity = hum;
-   pressure = pres;
-
-}

Arduino/Arduino_/Request.ino

@@ -1,80 +0,0 @@
-
-void sendRequest() {
-
-  getBME280Data();
-    
-  s = BASE_URL;
-  s.concat("windS=");
-  s.concat(windSpeed);
-  s.concat("&windD=");
-  s.concat(windDirection);
-  s.concat("&temp=");
-  s.concat(temperature);
-  s.concat("&pres=");
-  s.concat(pressure);
-  s.concat("&hum=");
-  s.concat(humidity);
-  s.toCharArray(URL, 100);
-
-  Serial.println(URL);
-  
-  // Establish GPRS connectivity (5 trials)
-  bool connected = false;
-  for(uint8_t i = 0; i < 5 && !connected; i++) {
-    delay(1000);
-    connected = sim800l->connectGPRS();
-  }
-
-  // Check if connected, if not reset the module and setup the config again
-  if(connected) {
-    Serial.println(F("GPRS connected !"));
-  } else {
-    Serial.println(F("GPRS not connected !"));
-    Serial.println(F("Reset the module."));
-    sim800l->reset();
-    setupSIM800L();
-    return;
-  }
-
-  Serial.println(F("Start HTTP GET..."));
-  Serial.println(URL);
-
-  // Do HTTP GET communication with 10s for the timeout (read)
-  uint16_t rc = sim800l->doGet(URL, 10000);
-   if(rc == 200) {
-    // Success, output the data received on the serial
-    Serial.print(F("HTTP GET successful ("));
-    Serial.print(sim800l->getDataSizeReceived());
-    Serial.println(F(" bytes)"));
-    Serial.print(F("Received : "));
-    Serial.println(sim800l->getDataReceived());
-  } else {
-    // Failed...
-    Serial.print(F("HTTP GET error "));
-    Serial.println(rc);
-  }
-
-  // Close GPRS connectivity (5 trials)
-  bool disconnected = sim800l->disconnectGPRS();
-  for(uint8_t i = 0; i < 5 && !connected; i++) {
-    delay(1000);
-    disconnected = sim800l->disconnectGPRS();
-  }
-
-  if(disconnected) {
-    Serial.println(F("GPRS disconnected !"));
-  } else {
-    Serial.println(F("GPRS still connected !"));
-  }
-
-  // Go into low power mode
-  bool lowPowerMode = sim800l->setPowerMode(MINIMUM);
-  if(lowPowerMode) {
-    Serial.println(F("Module in low power mode"));
-  } else {
-    Serial.println(F("Failed to switch module to low power mode"));
-  }
-
-  timer = millis() + timerLimit;
-  windSpeed = 0;
-}

Arduino/Arduino_/Setup.ino

@@ -1,58 +0,0 @@
-
-void setupSIM800L() {
-  // Wait until the module is ready to accept AT commands
-  while(!sim800l->isReady()) {
-    Serial.println(F("Problem to initialize AT command, retry in 1 sec"));
-    delay(1000);
-  }
-  Serial.println(F("Setup Complete!"));
-
-  // Wait for the GSM signal
-  uint8_t signal = sim800l->getSignal();
-  while(signal <= 0) {
-    delay(1000);
-    signal = sim800l->getSignal();
-  }
-  Serial.print(F("Signal OK (strenght: "));
-  Serial.print(signal);
-  Serial.println(F(")"));
-  delay(1000);
-
-  // Wait for operator network registration (national or roaming network)
-  NetworkRegistration network = sim800l->getRegistrationStatus();
-  while(network != REGISTERED_HOME && network != REGISTERED_ROAMING) {
-    delay(1000);
-    network = sim800l->getRegistrationStatus();
-  }
-  Serial.println(F("Network registration OK"));
-  delay(1000);
-
-  // Setup APN for GPRS configuration
-  bool success = sim800l->setupGPRS(APN);
-  while(!success) {
-    success = sim800l->setupGPRS(APN);
-    delay(5000);
-  }
-  Serial.println(F("GPRS config OK"));
-}
-
-
-void setupBME280() {
-  Wire.begin();
-
-  while(!bme.begin()) {
-    Serial.println("Could not find BME280 sensor!");
-    delay(1000);
-  }
-
-  switch(bme.chipModel()) {
-     case BME280::ChipModel_BME280:
-       Serial.println("Found BME280 sensor! Success.");
-       break;
-     case BME280::ChipModel_BMP280:
-       Serial.println("Found BMP280 sensor! No Humidity available.");
-       break;
-     default:
-       Serial.println("Found UNKNOWN sensor! Error!");
-  }
-}

Arduino/Sensors/Sensors.ino

@@ -27,6 +27,13 @@ void setup() {
   Serial.begin(9600);
   while(!Serial);
 
+  // Initialize a Wire
+  Wire.begin();
+   while(!bme.begin()){
+    Serial.println("Could not find BME280 sensor!");
+    delay(1000);
+  }
+
   // Initialize a SoftwareSerial
   sensor.begin(4800);
   delay(500);
@@ -36,10 +43,20 @@ void setup() {
 }
 
 void loop() {
+  
   getWind();
   Serial.print("Direction: ");
   Serial.println(windDirection);
   Serial.print("Speed: ");
   Serial.println(windSpeed);
+
+
+  getBME280Data();
+  Serial.print("Temp: ");
+  Serial.println(temperature);
+  Serial.print("Hum: ");
+  Serial.println(humidity);
+  Serial.print("Pres: ");
+  Serial.println(pressure);
   delay(5000);
 }